Gold Reserve Estimation Methods

Reserve Estimation and Placer Valuation: Methods that can be used for reserve estimation and placer valuation are (1) block method (2) triangle method (3) polygonal method (4) cross-section method (5) method of diamonds. After samples have been collected, washed, and assayed, reserves for a deposit can be estimated. There are many placer reserve estimation methods available. Some of these are the block, triangle, polygonal, traverses, and diamond methods.

* Block Method: The value using the block method is calculated as follows:
* 1) Find the volume of each block, length times width times depth.
* 2) Multiply the volume by the value per cubic meter (cubic yard) in each block,
* 3) Find the sum of all weighed values to obtain the total value.
* 4) Find the average grade by dividing the total in step 3 by the total volume to obtain the value per cubic meter (cubic yard).

Triangle Method: If this method is used, the value of deposit is calculated as follows:

  1. The volume equals the average of depth of the three drill holes times the area of the trian gle,
  2. The weighed average gold content is equal to the gold value of each of the three holes times the depth of each of the holes divided by the sum of the depths of the three holes.
  3. Total volume equals the summation of values in step 1.
  4. Total gold content equals the total volume in step 3 times the average from step 2.
  5. The average grade equals the total gold content in step 4 divided by the total volume in step 3.

Polygonal Method: Either method may be used in finding the value using polygons.
The grade for regular polygons is calculated as follows:

  1. The total volume equals the sum of the volumes of the individual polygons. Find the volume of the polygons by multiplying the area of the polygon times the depth of the drill hole.
  2. Total gold content equals the sum of the grades of each hole times the volume of each polygon.
  3. Average grade equals the value in step 2 divided by the value in step 1.
   The area of each irregular polygon may be found by using a planimeter or by dividing the polygon into triangles or rectangles.

Traverses Method: This method is very similar to that of the triangle and may be used as a check:

  1. Area of a traverse is the average of the depths of the boreholes times the distance between the boreholes.
  2. The total volume of a section between two traverses is one-half the sum of the areas of all individual traverses, A and B, times the distance between the traverses.
  3. The gold content of a section is the volume of the section times the average value between two traverses.
  4. The total gold content is the sum of the gold contents of each section.
  5. The average grade is the value in step 4 divided by the value in step 2.

Method of Diamonds: The method of diamonds is much the same as that of triangles. The drill hole is located at the centre of the diamond and apexes midway between drill holes on adjacent lines. This method is best used for regularly spaced holes. The total area is equal to the sum of all diamonds that may be treated as right triangles for all practical purposes:

  1. 1) Total volume equals the area of each diamond times the depth of each hole through the pay zone.
  2. 2) Total gold value equals the sum of the gold value in each hole times the volume of each diamond.
  3. 3) To find the value per cubic meter (cubic yard), divide the value in step 2 by the value in step 1.

There are many ways to sample and many methods to calculate the value of a placer deposit. It is important to remember to use care in sampling and to select the method that best suits the type of occurrence that is being sampled. Also, use the ore reserve calculation method that best applies to the configuration of the deposit and mode of deposition. Nothing replaces experience, not a costly site or advanced software. Gold, diamond or tin placer has a personality of its own, but all placers in a geological province area are similar. Also, placers formed in cold climates like Alaska or Yukon, are very different from tropical placers formed under laterization processes. A point often missed (for a time) by a placer specialist (geologist) shifting to new hunting grounds.